¿Cómo depurar desconexiones Wi-Fi repetidas en Arch Linux?

Después de intentar durante mucho tiempo obtener una conexión inalámbrica , ahora puedo obtener una conexión extremadamente incompleta (como en unos segundos de acceso real a Internet cada pocos minutos). Ejecutando wpa_supplicant -d -i wlp0s29f7u5 -c wifi.conf -Dwexten un VT y while ! yes | pacman -Syu; do :; doneen otro, después de varios minutos todavía no se hace, pero de vez en cuando se las arregla para descargar algunos archivos.

iw dev wlp0s29f7u5 link en la máquina Arch informa una potencia de la señal de aproximadamente -40 dB, que es mucho peor que la computadora portátil Ubuntu a -70 dB.

Salida de conexión:

# wpa_supplicant -d -i wlp0s29f7u5 -c wifi.conf -Dwext
wpa_supplicant v2.0
Successfully initialized wpa_supplicant
Initializing interface 'wlp0s29f7u5' conf 'wifi.conf' driver 'wext' ctrl_interface 'N/A' bridge 'N/A'
Configuration file 'wifi.conf' -> '/root/wifi.conf'
Reading configuration file '/root/wifi.conf'
ctrl_interface='/var/run/wpa_supplicant'
Priority group 0
   id=0 ssid='BTHub4-GRK6'
WEXT: cfg80211-based driver detected
wext: interface wlp0s29f7u5 phy: phy0
rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0
SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf
  capabilities: key_mgmt 0xf enc 0x1f flags 0x0
netlink: Operstate: linkmode=1, operstate=5
wlp0s29f7u5: Own MAC address: e8:4e:06:14:7a:77
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_countermeasures
wlp0s29f7u5: RSN: flushing PMKID list in the driver
wlp0s29f7u5: Setting scan request: 0 sec 100000 usec
WPS: Set UUID for interface wlp0s29f7u5
WPS: UUID based on MAC address - hexdump(len=16): 7c c4 e6 42 89 cb 59 26 95 2a b6 fd f8 85 e6 3a
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: Supplicant port status: Unauthorized
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: Supplicant port status: Unauthorized
EAPOL: Supplicant port status: Unauthorized
wlp0s29f7u5: Added interface wlp0s29f7u5
wlp0s29f7u5: State: DISCONNECTED -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlp0s29f7u5' added
WEXT: if_removed already cleared - ignore event
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlp0s29f7u5' added
WEXT: if_removed already cleared - ignore event
Wireless event: cmd=0x8b06 len=12
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlp0s29f7u5' added
WEXT: if_removed already cleared - ignore event
Wireless event: cmd=0x8b1a len=16
wlp0s29f7u5: State: DISCONNECTED -> SCANNING
wlp0s29f7u5: Starting AP scan for wildcard SSID
Scan requested (ret=0) - scan timeout 10 seconds
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlp0s29f7u5' added
WEXT: if_removed already cleared - ignore event
Wireless event: cmd=0x8b19 len=16
wlp0s29f7u5: Event SCAN_RESULTS (3) received
Received 838 bytes of scan results (2 BSSes)
wlp0s29f7u5: BSS: Start scan result update 1
wlp0s29f7u5: BSS: Add new id 0 BSSID cc:33:bb:13:8a:f4 SSID 'BTHub4-GRK6'
wlp0s29f7u5: BSS: Add new id 1 BSSID 00:22:b0:60:09:69 SSID 'leandro'
BSS: last_scan_res_used=2/32 last_scan_full=0
wlp0s29f7u5: New scan results available
wlp0s29f7u5: Selecting BSS from priority group 0
wlp0s29f7u5: 0: cc:33:bb:13:8a:f4 ssid='BTHub4-GRK6' wpa_ie_len=0 rsn_ie_len=24 caps=0x11 level=10
wlp0s29f7u5:    selected based on RSN IE
wlp0s29f7u5:    selected BSS cc:33:bb:13:8a:f4 ssid='BTHub4-GRK6'
wlp0s29f7u5: Request association: reassociate: 0  selected: cc:33:bb:13:8a:f4  bssid: 00:00:00:00:00:00  pending: 00:00:00:00:00:00  wpa_state: SCANNING
wlp0s29f7u5: Trying to associate with cc:33:bb:13:8a:f4 (SSID='BTHub4-GRK6' freq=2457 MHz)
wlp0s29f7u5: Cancelling scan request
wlp0s29f7u5: WPA: clearing own WPA/RSN IE
wlp0s29f7u5: Automatic auth_alg selection: 0x1
RSN: PMKSA cache search - network_ctx=(nil) try_opportunistic=0
RSN: Search for BSSID cc:33:bb:13:8a:f4
RSN: No PMKSA cache entry found
wlp0s29f7u5: RSN: using IEEE 802.11i/D9.0
wlp0s29f7u5: WPA: Selected cipher suites: group 8 pairwise 24 key_mgmt 2 proto 2
wlp0s29f7u5: WPA: clearing AP WPA IE
WPA: set AP RSN IE - hexdump(len=26): 30 18 01 00 00 0f ac 02 02 00 00 0f ac 04 00 0f ac 02 01 00 00 0f ac 02 00 00
wlp0s29f7u5: WPA: using GTK TKIP
wlp0s29f7u5: WPA: using PTK CCMP
wlp0s29f7u5: WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPAioctl[SIOCSIWFREQ]: Device or resource busy
 IE default - hexdump(len=22): 30 14 01 00 00 0f ac 02 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
wlp0s29f7u5: No keys have been configured - skip key clearing
wlp0s29f7u5: State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
Limit connection to BSSID cc:33:bb:13:8a:f4 freq=2457 MHz based on scan results (bssid_set=0)
wlp0s29f7u5: set_disable_max_amsdu: -1
wlp0s29f7u5: set_ampdu_factor: -1
wlp0s29f7u5: set_ampdu_density: -1
wlp0s29f7u5: set_disable_ht40: 0
wlp0s29f7u5: set_disable_sgi: 0
wpa_driver_wext_associate
wpa_driver_wext_set_drop_unencrypted
wpa_driver_wext_set_psk
wlp0s29f7u5: Association request to the driver failed
wlp0s29f7u5: Setting authentication timeout: 5 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - EAP fail=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - portControl=Auto
EAPOL: Supplicant port status: Unauthorized
RSN: Ignored PMKID candidate without preauth flag
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlp0s29f7u5' added
WEXT: if_removed already cleared - ignore event
Wireless event: cmd=0x8b1a len=16
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlp0s29f7u5' added
WEXT: if_removed already cleared - ignore event
Wireless event: cmd=0x8b06 len=12
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlp0s29f7u5' added
WEXT: if_removed already cleared - ignore event
Wireless event: cmd=0x8b1a len=27
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlp0s29f7u5' added
WEXT: if_removed already cleared - ignore event
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlp0s29f7u5' added
WEXT: if_removed already cleared - ignore event
Wireless event: cmd=0x8c08 len=65
AssocResp IE wireless event - hexdump(len=49): 01 04 82 84 0b 16 32 08 0c 12 18 24 30 48 60 6c dd 18 00 50 f2 02 01 01 08 00 03 a4 00 00 27 a4 00 00 42 43 5e 00 62 32 2f 00 dd 05 00 09 86 01 00
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlp0s29f7u5' added
WEXT: if_removed already cleared - ignore event
Wireless event: cmd=0x8b15 len=24
Wireless event: new AP: cc:33:bb:13:8a:f4
wlp0s29f7u5: Event ASSOCINFO (4) received
wlp0s29f7u5: Association info event
resp_ies - hexdump(len=49): 01 04 82 84 0b 16 32 08 0c 12 18 24 30 48 60 6c dd 18 00 50 f2 02 01 01 08 00 03 a4 00 00 27 a4 00 00 42 43 5e 00 62 32 2f 00 dd 05 00 09 86 01 00
wlp0s29f7u5: Event ASSOC (0) received
wlp0s29f7u5: State: ASSOCIATING -> ASSOCIATED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
wlp0s29f7u5: Associated to a new BSS: BSSID=cc:33:bb:13:8a:f4
wlp0s29f7u5: No keys have been configured - skip key clearing
wlp0s29f7u5: Associated with cc:33:bb:13:8a:f4
wlp0s29f7u5: WPA: Association event - clear replay counter
wlp0s29f7u5: WPA: Clear old PTK
EAPOL: External notification - portEnabled=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - portValid=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - EAP success=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: SUPP_BE entering state IDLE
wlp0s29f7u5: Setting authentication timeout: 10 sec 0 usec
wlp0s29f7u5: Cancelling scan request
wlp0s29f7u5: RX EAPOL from cc:33:bb:13:8a:f4
wlp0s29f7u5: Setting authentication timeout: 10 sec 0 usec
wlp0s29f7u5: IEEE 802.1X RX: version=1 type=3 length=95
wlp0s29f7u5:   EAPOL-Key type=2
wlp0s29f7u5:   key_info 0x8a (ver=2 keyidx=0 rsvd=0 Pairwise Ack)
wlp0s29f7u5:   key_length=16 key_data_length=0
  replay_counter - hexdump(len=8): 00 00 00 00 00 00 00 01
  key_nonce - hexdump(len=32): c8 c9 ae c3 18 6c 23 4a a0 38 99 55 ec 9c c5 da ad 2d 00 dd 7a b3 33 c2 20 8b ab 41 e5 cd 1e b6
  key_iv - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  key_rsc - hexdump(len=8): 00 00 00 00 00 00 00 00
  key_id (reserved) - hexdump(len=8): 00 00 00 00 00 00 00 00
  key_mic - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
wlp0s29f7u5: State: ASSOCIATED -> 4WAY_HANDSHAKE
wlp0s29f7u5: WPA: RX message 1 of 4-Way Handshake from cc:33:bb:13:8a:f4 (ver=2)
RSN: msg 1/4 key data - hexdump(len=0):
WPA: Renewed SNonce - hexdump(len=32): ab ec fb 19 6f 98 4a 00 75 78 4a 0d e0 37 fd d2 c3 44 29 66 2b 7e 93 57 06 0a f5 68 1b 02 aa fa
WPA: PTK derivation - A1=e8:4e:06:14:7a:77 A2=cc:33:bb:13:8a:f4
WPA: Nonce1 - hexdump(len=32): ab ec fb 19 6f 98 4a 00 75 78 4a 0d e0 37 fd d2 c3 44 29 66 2b 7e 93 57 06 0a f5 68 1b 02 aa fa
WPA: Nonce2 - hexdump(len=32): c8 c9 ae c3 18 6c 23 4a a0 38 99 55 ec 9c c5 da ad 2d 00 dd 7a b3 33 c2 20 8b ab 41 e5 cd 1e b6
WPA: PMK - hexdump(len=32): [REMOVED]
WPA: PTK - hexdump(len=48): [REMOVED]
WPA: WPA IE for msg 2/4 - hexdump(len=22): 30 14 01 00 00 0f ac 02 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
WPA: Replay Counter - hexdump(len=8): 00 00 00 00 00 00 00 01
wlp0s29f7u5: WPA: Sending EAPOL-Key 2/4
WPA: KCK - hexdump(len=16): [REMOVED]
WPA: Derived Key MIC - hexdump(len=16): c1 ea 02 f5 f1 e3 47 51 44 b9 05 4b 04 37 bc 2a
wlp0s29f7u5: RX EAPOL from cc:33:bb:13:8a:f4
wlp0s29f7u5: IEEE 802.1X RX: version=1 type=3 length=175
wlp0s29f7u5:   EAPOL-Key type=2
wlp0s29f7u5:   key_info 0x13ca (ver=2 keyidx=0 rsvd=0 Pairwise Install Ack MIC Secure Encr)
wlp0s29f7u5:   key_length=16 key_data_length=80
  replay_counter - hexdump(len=8): 00 00 00 00 00 00 00 02
  key_nonce - hexdump(len=32): c8 c9 ae c3 18 6c 23 4a a0 38 99 55 ec 9c c5 da ad 2d 00 dd 7a b3 33 c2 20 8b ab 41 e5 cd 1e b6
  key_iv - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  key_rsc - hexdump(len=8): da 02 00 00 00 00 00 00
  key_id (reserved) - hexdump(len=8): 00 00 00 00 00 00 00 00
  key_mic - hexdump(len=16): 4c 67 eb c0 a0 be 0f ac 28 36 7d da e5 f2 b9 08
RSN: encrypted key data - hexdump(len=80): a5 39 e0 01 c0 2b 4b 12 f5 2d de e5 5f 1e 41 a3 f7 27 13 a6 cc 9a 94 a7 cb a5 7c 69 1c 3e 0f 4c 93 a5 93 7b cc c3 2b fc 20 47 ba d5 f3 60 5f c9 70 cb 71 b1 01 81 31 95 b0 a3 15 ef b6 fe f4 87 02 6d 7d f7 11 02 db b4 c3 92 ea ce 6e f3 a9 13
WPA: decrypted EAPOL-Key key data - hexdump(len=72): [REMOVED]
wlp0s29f7u5: State: 4WAY_HANDSHAKE -> 4WAY_HANDSHAKE
wlp0s29f7u5: WPA: RX message 3 of 4-Way Handshake from cc:33:bb:13:8a:f4 (ver=2)
WPA: IE KeyData - hexdump(len=72): 30 18 01 00 00 0f ac 02 02 00 00 0f ac 04 00 0f ac 02 01 00 00 0f ac 02 00 00 dd 26 00 0f ac 01 01 00 9c 1c 9f 0b f1 8d 96 63 e1 a9 8e e6 f8 74 95 71 ee 71 65 d5 e5 3e df 4c 42 ae 80 a1 e3 b1 a7 5f dd 00 00 00 00 00
WPA: RSN IE in EAPOL-Key - hexdump(len=26): 30 18 01 00 00 0f ac 02 02 00 00 0f ac 04 00 0f ac 02 01 00 00 0f ac 02 00 00
WPA: GTK in EAPOL-Key - hexdump(len=40): [REMOVED]
wlp0s29f7u5: WPA: Sending EAPOL-Key 4/4
WPA: KCK - hexdump(len=16): [REMOVED]
WPA: Derived Key MIC - hexdump(len=16): f9 ab 08 31 3c b6 d4 55 6b 2f 39 9d bb 9a 99 a8
wlp0s29f7u5: WPA: Installing PTK to the driver
wpa_driver_wext_set_key: alg=3 key_idx=0 set_tx=1 seq_len=6 key_len=16
EAPOL: External notification - portValid=1
wlp0s29f7u5: State: 4WAY_HANDSHAKE -> GROUP_HANDSHAKE
RSN: received GTK in pairwise handshake - hexdump(len=34): [REMOVED]
WPA: Group Key - hexdump(len=32): [REMOVED]
wlp0s29f7u5: WPA: Installing GTK to the driver (keyidx=1 tx=0 len=32)
WPA: RSC - hexdump(len=6): da 02 00 00 00 00
wpa_driver_wext_set_key: alg=2 key_idx=1 set_tx=0 seq_len=6 key_len=32
wlp0s29f7u5: WPA: Key negotiation completed with cc:33:bb:13:8a:f4 [PTK=CCMP GTK=TKIP]
wlp0s29f7u5: Cancelling authentication timeout
wlp0s29f7u5: State: GROUP_HANDSHAKE -> COMPLETED
wlp0s29f7u5: CTRL-EVENT-CONNECTED - Connection to cc:33:bb:13:8a:f4 completed [id=0 id_str=]
wpa_driver_wext_set_operstate: operstate 0->1 (UP)
netlink: Operstate: linkmode=-1, operstate=6
EAPOL: External notification - portValid=1
EAPOL: External notification - EAP success=1
EAPOL: SUPP_PAE entering state AUTHENTICATING
EAPOL: SUPP_BE entering state SUCCESS
EAP: EAP entering state DISABLED
EAPOL: SUPP_PAE entering state AUTHENTICATED
EAPOL: Supplicant port status: Authorized
EAPOL: SUPP_BE entering state IDLE
EAPOL authentication completed successfully
RTM_NEWLINK: operstate=1 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlp0s29f7u5' added
WEXT: if_removed already cleared - ignore event
EAPOL: startWhen --> 0
EAPOL: disable timer tick
RTM_NEWLINK: operstate=1 ifi_flags=0x1003 ([UP])

Información del dispositivo:

# lsusb | grep WLAN
Bus 004 Device 004: ID 0bda:8178 Realtek Semiconductor Corp. RTL8192CU 802.11n WLAN Adapter

Firmware: rtlwifi/rtl8192cufw.bin

Controlador de interfaz: rtl8192cu

OS:

# uname -a
Linux archiso 3.10.10-1-ARCH #1 SMP PREEMPT Fri Aug 30 11:30:06 CEST 2013 x86_64 GNU/Linux

El progreso generalmente se detiene en la EAPOL: disable timer ticklínea durante algunos segundos antes de continuar.

¿Alguna idea sobre que podría ir mal? La salida es principalmente griega para mí.

¿Debo hacer algo más en segundo plano, como renovar el contrato de arrendamiento de DHCP, cuando se establece la conexión para utilizarlo lo antes posible?

Y finalmente, ¿se considera que -40 dB es una calidad de enlace "soportable"?

Actualización : dmesgahora tengo una enorme cantidad de cosas como esta:

wlp0s29f7u5: Connection to AP cc:33:bb:13:8a:f4 lost
cfg80211: Calling CRDA to update world regulatory domain
wlp0s29f7u5: authenticate with cc:33:bb:13:8a:f4
wlp0s29f7u5: send auth to cc:33:bb:13:8a:f4 (try 1/3)
wlp0s29f7u5: send auth to cc:33:bb:13:8a:f4 (try 2/3)
wlp0s29f7u5: send auth to cc:33:bb:13:8a:f4 (try 3/3)
wlp0s29f7u5: authentication with cc:33:bb:13:8a:f4 timed out
wlp0s29f7u5: authenticate with cc:33:bb:13:8a:f4
wlp0s29f7u5: send auth to cc:33:bb:13:8a:f4 (try 1/3)
wlp0s29f7u5: authenticated
wlp0s29f7u5: associating with AP with corrupt beacon and probe response
wlp0s29f7u5: associate with cc:33:bb:13:8a:f4 (try 1/3)
wlp0s29f7u5: RX AssocResp from cc:33:bb:13:8a:f4 (capab=0x431 status=0 aid=24)
wlp0s29f7u5: associated
wlp0s29f7u5: Connection to AP cc:33:bb:13:8a:f4 lost
cfg80211: Calling CRDA for country: PL
wlp0s29f7u5: authenticate with cc:33:bb:13:8a:f4
wlp0s29f7u5: send auth to cc:33:bb:13:8a:f4 (try 1/3)
wlp0s29f7u5: send auth to cc:33:bb:13:8a:f4 (try 2/3)
wlp0s29f7u5: send auth to cc:33:bb:13:8a:f4 (try 3/3)
wlp0s29f7u5: authentication with cc:33:bb:13:8a:f4 timed out
wlp0s29f7u5: authenticate with cc:33:bb:13:8a:f4
wlp0s29f7u5: send auth to cc:33:bb:13:8a:f4 (try 1/3)
wlp0s29f7u5: authenticated
wlp0s29f7u5: associating with AP with corrupt beacon and probe response
wlp0s29f7u5: associate with cc:33:bb:13:8a:f4 (try 1/3)
wlp0s29f7u5: RX AssocResp from cc:33:bb:13:8a:f4 (capab=0x431 status=0 aid=24)
wlp0s29f7u5: associated
wlp0s29f7u5: Connection to AP cc:33:bb:13:8a:f4 lost

Aquí hay una serie de cosas raras:

• ¿Qué es una "respuesta de sonda y baliza corrupta" y cómo lo soluciono?
• ¿Por qué cree que estoy en Polonia cuando estoy en el Reino Unido?
• ¿Por qué los primeros tres intentos de conexión siempre exceden el tiempo de espera mientras el cuarto tiene éxito?

El problema es su configuración wpa_supplicant; primero -Dwext es viejo. use -Dnl80211 segundo; no agregue nada más que net.lo y net.wlp0s29f7u5 a su secuencia de comandos inicial y agréguelos en el momento del arranque para cargar. tercero; eliminar cualquier cosa como NetworkManager o Wicd cuarto; Limpie su archivo de red y config_wlp0s29f7u5 = "dhcp". Esto será útil si utiliza dhcp en su conexión WIFI. también en su terminal con acceso de superusuario tipo dhcpcd . solo por diversión; puede resolver mucho dolor